Electrical interface: | |
---|---|
Color: | |
Voltage: | |
working temperature: | |
Availability: | |
Quantity: | |
PDF Export | |
Standard Industrial IoT MINI Smart Cloud Box for Smart Lighting Pole
Introduction:
WE-GW-G40 complies with IEEE802.3U and IEEE802.3z 1000Base-Tx/Fx protocols, and supports full duplex/half duplex mode. Customers can choose the right product according to the following references.
Selection guide:
Our product naming rules (IS***F*T-**-XX, ISG1F4T-S20-XX is taken as an example below)
IS | G | 1F | 4T | S | 20 | XX |
IS— | F-100 trillion | 1F— 1 Light mouth | 1T—1 Electrical interface | M-Multimode | 20-20KM | |
Industry Switch | G-Gigabit | 2F— 2 Light mouth | 2T—2 Electrical interface | S-Single mode | 40-40KM | customize |
ISP— | 3F— 3 Light mouth | 3T—3 Electrical interface | A-Single fiber 1310 | 60-60KM | ||
Industry POE | 4F— 4 Light mouth | 4T—4 Electrical interface | B-Single fiber 1550 | 80-80KM | ||
Change machine | And so on | And so on | SFP | And so on |
Installation:
1. Interface
● RJ-45 interface
It supports CAT5 twisted pair cables up to 100 meters long, and supports automatic switching between parallel and crossover cables (MDI-MDIX).
● Optical interface
Support SC/ST/FC/LC optical fiber interface, dual-fiber optical interface has two sockets (TX, RX), single-fiber optical interface has only one socket. When the optical interface is cascaded with the transceiver or switch at the opposite end, the dual-fiber type should be cross-connected, and the single-fiber type can be connected directly.
● Prompt
1. This product is suitable for various industrial environments and indoor and outdoor environments;
2. When not using the optical port, please plug in the optical port dust cover;
3. It is forbidden to observe the TX port directly with eyes to prevent the laser from hurting the eyes;
4. Single fiber products must be used in pairs.
● Troubleshooting
1. The equipment does not match. If the equipment connected to this product (network card, hub, switch) does not match, please select a suitable product according to the rate (10M, 100M, 1000M);
2. The optical fiber indicator does not light up, consider the fiber line loss is too large. Fiber wiring, fiber fusion splicing, or improper fiber jumper plugs may cause excessive loss and cause the equipment to work abnormally.
● Packing list
Before installing the equipment, please check in detail whether it contains the following items:
Industrial Grade Fiber Switch
Power cord (only when equipped with power supply)
Adapter (optional)
User manual
Main features:
1. Comply with IEEE 802.3 10 Base-T, IEEE 802.3u 100 Base-TX, IEEE802.3z standards;
2. Built-in high-efficiency SRAM data storage space and 1K lookup table, equipped with 4-way hash algorithm;
3. Support back pressure flow control, IEEE802.3 X and half duplex;
4. Support automatic switching between parallel lines and cross lines;
5. Comply with FCC and 15 CLASS A and CE standards
Technical parameter:
standard | Comply with IEEE802.3 10 Base-T, IEEE 802.3u 100Base-TX, IEEE802.3z and other standards |
Electrical interface | RJ45, supporting Category 5 or Category 6 unshielded twisted pair |
Optical interface | SC/ST/FC/LC |
Mode | Support full duplex and half duplex mode |
Power supply | 110-265V AC;DC10-55V |
Storage temperature | -40℃-85 ℃ |
Operating temperature | -40℃-85 ℃ |
Relative humidity | 5%-95%; |
Applicable | Multimode:50/125, 62.5/125 or 100/140 Micron |
fiber | Single mode:8.3/125, 8.7/125, 9/125 or 10/125 Micron |
Physical dimension | 130 mm x 94 mm x 35 mm |
● Connection
The optical fiber interface can be connected to the network to be accessed, and other electrical interfaces can be connected to terminal equipment such as switches or computers. Both optical and electrical ports can be cascaded with any one of them, and the specific usage method can be flexibly configured according to the actual situation on site. When the optical fiber or network cable is connected, the LED indicator of the corresponding port should light up, prompting the user that the device is connected normally.
Factory:
Standard Industrial IoT MINI Smart Cloud Box for Smart Lighting Pole
Introduction:
WE-GW-G40 complies with IEEE802.3U and IEEE802.3z 1000Base-Tx/Fx protocols, and supports full duplex/half duplex mode. Customers can choose the right product according to the following references.
Selection guide:
Our product naming rules (IS***F*T-**-XX, ISG1F4T-S20-XX is taken as an example below)
IS | G | 1F | 4T | S | 20 | XX |
IS— | F-100 trillion | 1F— 1 Light mouth | 1T—1 Electrical interface | M-Multimode | 20-20KM | |
Industry Switch | G-Gigabit | 2F— 2 Light mouth | 2T—2 Electrical interface | S-Single mode | 40-40KM | customize |
ISP— | 3F— 3 Light mouth | 3T—3 Electrical interface | A-Single fiber 1310 | 60-60KM | ||
Industry POE | 4F— 4 Light mouth | 4T—4 Electrical interface | B-Single fiber 1550 | 80-80KM | ||
Change machine | And so on | And so on | SFP | And so on |
Installation:
1. Interface
● RJ-45 interface
It supports CAT5 twisted pair cables up to 100 meters long, and supports automatic switching between parallel and crossover cables (MDI-MDIX).
● Optical interface
Support SC/ST/FC/LC optical fiber interface, dual-fiber optical interface has two sockets (TX, RX), single-fiber optical interface has only one socket. When the optical interface is cascaded with the transceiver or switch at the opposite end, the dual-fiber type should be cross-connected, and the single-fiber type can be connected directly.
● Prompt
1. This product is suitable for various industrial environments and indoor and outdoor environments;
2. When not using the optical port, please plug in the optical port dust cover;
3. It is forbidden to observe the TX port directly with eyes to prevent the laser from hurting the eyes;
4. Single fiber products must be used in pairs.
● Troubleshooting
1. The equipment does not match. If the equipment connected to this product (network card, hub, switch) does not match, please select a suitable product according to the rate (10M, 100M, 1000M);
2. The optical fiber indicator does not light up, consider the fiber line loss is too large. Fiber wiring, fiber fusion splicing, or improper fiber jumper plugs may cause excessive loss and cause the equipment to work abnormally.
● Packing list
Before installing the equipment, please check in detail whether it contains the following items:
Industrial Grade Fiber Switch
Power cord (only when equipped with power supply)
Adapter (optional)
User manual
Main features:
1. Comply with IEEE 802.3 10 Base-T, IEEE 802.3u 100 Base-TX, IEEE802.3z standards;
2. Built-in high-efficiency SRAM data storage space and 1K lookup table, equipped with 4-way hash algorithm;
3. Support back pressure flow control, IEEE802.3 X and half duplex;
4. Support automatic switching between parallel lines and cross lines;
5. Comply with FCC and 15 CLASS A and CE standards
Technical parameter:
standard | Comply with IEEE802.3 10 Base-T, IEEE 802.3u 100Base-TX, IEEE802.3z and other standards |
Electrical interface | RJ45, supporting Category 5 or Category 6 unshielded twisted pair |
Optical interface | SC/ST/FC/LC |
Mode | Support full duplex and half duplex mode |
Power supply | 110-265V AC;DC10-55V |
Storage temperature | -40℃-85 ℃ |
Operating temperature | -40℃-85 ℃ |
Relative humidity | 5%-95%; |
Applicable | Multimode:50/125, 62.5/125 or 100/140 Micron |
fiber | Single mode:8.3/125, 8.7/125, 9/125 or 10/125 Micron |
Physical dimension | 130 mm x 94 mm x 35 mm |
● Connection
The optical fiber interface can be connected to the network to be accessed, and other electrical interfaces can be connected to terminal equipment such as switches or computers. Both optical and electrical ports can be cascaded with any one of them, and the specific usage method can be flexibly configured according to the actual situation on site. When the optical fiber or network cable is connected, the LED indicator of the corresponding port should light up, prompting the user that the device is connected normally.
Factory: